Search Results

The advancements made in modeling and parameter identification of nonlinear isolation components in the underlying investigation confirm the importance of accurate Multibody Dynamics modeling of these components for reducing vibration and/or improving ride comfort. Considering dynamic stiffness and loss angle characteristics, the proposed nonlinear isolation component uses the Bouc/Wen hysteresis model for excitation amplitude dependency and a transfer function for excitation frequency dependency. Various combinations of Bouc/Wen hysteresis parameters result in different shapes for hysteresis loops and allows for modeling a wide range of soft and stiff isolator characteristics. The effect of the proposed isolation component on ride studies is illustrated by simulating a maneuver on a road profile using the OpenCRG road description with SimXpert Motion Workspace and Adams/Car. Tire belt dynamics are captured by adding a rigid ring part to the PAC2002 tire model [ 1 ].

This paper proposes a rolling machine that forms fine corrugated section patterns for thin sheets. A prototype of the machine was made and the performance of the machine was tested. As compared with press forming, rolling has the advantages of the high forming limit, the low forming reaction force, the easy control of the thin sheet's curve and high productivity. We confirmed these four advantages by using finite element analyses and the prototype rolling machine. Stainless steel sheets and titanium sheets, which were one of the materials with a low forming limit, were used. Firstly, the rolling showed a 1.3-times higher forming limit than the press forming in the case that a fine corrugated section pattern was formed in a stainless steel sheet of 22-mm square sizes. Secondly, the forming reaction force of the rolling was about one-twentieth of the press forming without coining, and the experimental results agreed with the finite element simulation.

With the increasing demand for fuel efficient vehicles, technologies like superplastic forming (SPF) are being developed and implemented to allow for the utilization of lightweight automotive sheet materials. While forming under superplastic conditions leads to increased formability in lightweight alloys, such as aluminum, the slower forming times required by the technology can limit the technology to low to mid production levels. One problem that can increase forming time is the reduction of forming pressure due to pressurizing (forming) gas leaks, during the forming cycle, at the die/sheet/blankholder interface. Traditionally, such leaks have been successfully addressed through the use of a seal bead. However, for advanced die technologies that result in reduced cycle times (such as hot draw mechanical performing, which combine aspects of mechanical preforming of the sheet metal followed by SPF), the use of seal beads can restrict the drawing of sheet material into the forming die.

Ultrasonic spot welds were made between sheets of 0.8-mm-thick hot-dip-galvanized mild steel and 1.6-mm-thick AZ31B-H24. Lap-shear strengths of 3.0-4.2 kN were achieved with weld times of 0.3-1.2 s. Failure to achieve strong bonding of joints where the Zn coating was removed from the steel surface indicate that Zn is essential to the bonding mechanism. Microstructure characterization and microchemical analysis indicated temperatures at the AZ31-steel interfaces reached at least 344°C in less than 0.3 s. The elevated temperature conditions promoted annealing of the AZ31-H24 metal and chemical reactions between it and the Zn coating.

Friction Stir Spot Welding (FSSW) is a relatively new solid state joining technology that has the potential to be a replacement for single point joining processes like Resistance Spot Welding and rivet technology in certain applications. Since the material flow around the pin plays an important role in determining the quality of the weld, understanding how the material moves is important to optimize process parameters and to validate the results of numerical simulations of the process. In this paper, an experimental study aimed at visualizing the material flow during the plunge phase of refill FSSW of an aluminum alloy is presented. Different marker materials were placed at a certain depth from the plate surface and metallographic samples in three mutually perpendicular directions were prepared and examined to identify the final location of the marker material after the plunge of the pin.

Forming simulation is a widely used tool to estimate production forming capabilities. During the last three to four years the prediction of process robustness by sensitivity analysis has been developed for industrial applications. The change of material parameters is one key figure and has a large impact on the final findings. Thus the user has to ensure that the variations done are in correlation with real material behaviour and the selected numerical model is reliable. Up to now the permitted changes in modelling are seldom secured by real measurements, especially when more advanced material models and hardening options are applied. Various materials chosen out of the production process for mild steel grades have been investigated for their mechanical properties using different tests. The limits of failure are defined by a reduced number of Nakajima tests to predict the forming limit curve (FLC). All data is prepared in the same manner to meet simulation program needs.

Incremental Sheet Forming (ISF) is an emerging sheet metal prototyping technology where a part is formed as one or more stylus tools are moving in a pre-determined path and deforming the sheet metal locally while the sheet blank is clamped along its periphery. A deformation analysis of incremental forming process is presented in this paper. The analysis includes the development of an analytical model for strain distributions based on part geometry and tool paths; and numerical simulations of the forming process with LS-DYNA. A skew cone is constructed and used as an example for the study. Analytical and numerical results are compared, and excellent correlations are found. It is demonstrated that the analytical model developed in this paper is reliable and efficient in the prediction of strain distributions for incremental forming process.

This paper presents a methodology for simulating Fluid Structure Interaction (FSI) for a typical vehicle bonnet (hood) under a range of onset flow conditions. The hood was chosen for this study, as it is one of the panels most prone to vibration; particularly given the trend to make vehicle panels lighter. Among the worst-case scenarios for inducing vibration is a panel being subjected to turbulent flow from vehicle wakes, and the sudden peak loads caused by emerging from a vehicle wake. This last case is typical of a passing manoeuvre, with the vehicle suddenly transitioning from being immersed in the wake of the leading vehicle, to being fully exposed to the free-stream flow. The transient flowfield was simulated for a range of onset flow conditions that could potentially be experienced on the open road, which may cause substantial vibration of susceptible vehicle panels.

This work details the process employed to design the 2009 Cooper Union FSAE® suspension system, spanning the overarching design philosophy, configuration selection, analysis, fabrication, and implementation, while offering recommendations to those especially new to the field. The design methodology illustrated here provides a systematic approach to suspension geometry, material selection, packaging, and construction. Though this paper serves as a starting point for FSAE® suspension designers, it provides a succinct overview for those interested in general suspension design fundamentals. The design process began with the selection of a suspension configuration, geometries, and kinematics, which were driven in part by tire data, desired bulk vehicle dynamics characteristics, and overall geometric variability. The springs and adjustable dampers were then selected as the front and rear anti-roll bar properties were concurrently designed.

Quasi-static tensile properties of TRIP590 steels from three different manufacturers were investigated using digital image correlation (DIC). The focus was on the post-uniform elongation behavior which can be very different for steels of the same grade owing to different manufacturing processes. Miniature tensile specimens, cut at 0°, 45°, and 90° relative to the rolling direction, were strained to failure in an instrumented tensile stage. True stress-true strain curves were computed from digital strain gages superimposed on digital images captured from one gage section surface during tensile deformation. Microstructural phases in undeformed and fracture specimens were identified with optical microscopy using the color tint etching process. Fracture surface analyses conducted with scanning electron microscopy and energy dispersive spectroscopy were used to investigate microvoids and inclusions in all materials.

Mechanical properties, formability and crash worthiness of a new sheet steel having an ultrafine grained (UFG) multi-phase (MP) microstructure are shown. The fabricated UFG-MP steel showed significant work hardening caused by deformation induced martensitic transformation of retained austenite, which resulted in a combination of high strength and large tensile elongation. It was confirmed by dynamic collapse test and FEM simulation that the large work hardenability of the UFG-MP steel promoted compact mode collapse that improved the absorbed energy.

Quasi-static axial cutting of AA6061-T6 and T4 round extrusions were completed using a specially designed cutter with multiple blades. The round specimens had a length of 200 mm, a nominal outer diameter of 50.8 mm, and a wall thickness of 3.175 mm or 1.587 mm. Four different cutters, constructed from heat-treated 4140 steel, having 3, 4, 5 and 6 blades on each cutter with a nominal tip width of 1.0 mm were used to penetrate through the round extrusions. A clean cutting mode was observed for the AA6061-T6 and T4 extrusions with wall thickness of 3.175 mm with an almost constant steady state cutting force. A braided cutting mode was observed for extrusions with both tempers with wall thickness of 1.587 mm, which resulted in a slightly oscillating steady state cutting force. For all extrusions with a wall thickness of 3.175 mm, the steady state cutting force increased with an increase in the number of cutter blades.

In response to the growing demand for fuel economy, we are developing a high-efficient variable displacement pump for hydraulic power steering systems. In order to develop a quiet variable displacement pump which generates lower noise for better vehicle interior sound quality, we have been developing a simulation tool which includes hydraulic analysis, vibration analysis, and vehicle interior noise analysis which combines simulation outputs and measured noise transfer functions of the targeted vehicle. This paper provides both validation results of the simulation tool and application examples to design improvement to conclude the effectiveness of the simulation tool developed.

Intensive R&D is currently performed worldwide on hybrid and electric vehicles. For full electric vehicles the driving range is limited by the capacity of currently available batteries. If such a vehicle shall increase its driving range some range extending backup system should be available. Such a Range Extender is a small system of combustion engine and electric generator which produces the required electricity for charging the batteries in time. Since the acoustic response of an electric motor driving the vehicle and of a combustion engine as part of a Range Extender is very different by nature an extensive acoustic tuning of the Range Extender is necessary to meet the requirements of exterior vehicle noise and passenger comfort. This paper describes the NVH (noise, vibration & harshness) development work of a range extender within the AVL approach of an electrically driven passenger car with range extender.

In the automotive industry, the use of beading is widely spread. Beads are primarily used to stiffen the floor and dash panels. The aim is to reduce vibration levels and hopefully at the same time reduce radiated noise. Beading has a positive effect close to the first panel mode's natural frequency however it can have a negative effect at all other frequencies. Typically, engineers assume a radiation efficiency of “1” (one) over the whole frequency range for simplicity or lack of available implemented formulation in their simulation tools. This assumption directs the investigation at reducing the vibration levels only. This approach can be misleading because even though radiation efficiency tends to “1” (one) above coincident frequency it is not the case below coincidence. While increasing stiffness reduces vibration levels, it also increases radiation efficiency. This can yield to higher levels of radiated noise.

For many technical applications it is necessary to avoid or to reduce vibrations. Factors benefiting from vibration reduction are for example the durability of the application, which is increased, as well as cost expenses and the level of noise, which are both decreased. Rough, bolted interfaces are common in most machines and can be used as damping devices with some effort. Perhaps in future such contact surfaces could be used as damping devices at the interfaces of an automotive engine or exhaust system. Nevertheless it is difficult to predict the effect of a change in contact interface parameters on the dynamic behavior of the entire mechanical system. Therefore a method for calculating the steady state behavior of elastic multi-body systems was developed. The basis of this method is a finite element model of each contacting unit. On each model a modal reduction is applied in order to reduce the degrees of freedom.

To uprate a 6-Cylinder In-line engine from 123 kW to 165 kW in power and upgrade the emission from Euro-2 to Euro-3 it was required to go for higher peak-firing pressures (PFP). The capability of Engine's Crankshaft to withstand the PFP was increased from 125 bar to 150 bar, maintaining the same cylinder centre distance. A crank-train model was used to achieve the required crankshaft strength for infinite fatigue life. The three aspects of crankshaft design, namely, crank strength, bearing selection, journal-pin lubrication and torsional vibration were considered during the design stage. The strength to withstand 150 bar PFP was achieved by increasing the crank web-thickness. To maintain the same cylinder centre distance, crankpin and main-journal lengths were reduced. Increased throw stiffness was achieved by increasing the crankpin diameter to improve crankshaft torsional behaviour.

To predict and minimize squeal propensity in brake systems, numerous models, which perform friction induced vibration, are available. However, today there is no model that can explain satisfactorily the dynamic behavior of brake systems. We argue that this is - among other effects - because existing models are based on decaying or constant coefficient of friction, although many investigations indicate rich dynamics of the coefficient of friction. Stability analysis of linear differential equations with periodic coefficients shows that instability regions change with rising amplitude of the periodic coefficients. If the periodic coefficient corresponds to the coefficient of friction, its periodicity can lower the stability of a minimal model.

The riveting process with a solid rivet is one of the most applied joining processes in the aeronautic industry. New materials and new design requirements constitute challenges that drive the users to a better understanding of the installation process of riveted joints. Therefore, this study aims with the aid of FEM simulation to understand the phenomena occurring during the installation process and afterwards to predict the mechanical properties of the riveted joint depending on the installation parameters and characteristics of the adherends. The experimental installation process for the validation of the simulation model takes place in a fully automated C-frame riveting machine with all-electric drilling and riveting operations aptitude and continuous collection of process data. This paper deals with the simulation of the installation process. The simulation model consists of a solid rivet with universal head described by the standard EN6081 and aluminum (2024-T351) adherends.

Serial link articulated robots applied in aerospace assembly have largely been limited in scope by deficiencies in positional accuracy. The majority of aerospace applications require tolerances of +/−0.25mm or less which have historically been far beyond reach of the conventional off-the-shelf robot. The recent development of the accurate robot technology represents a paradigm shift for the use of articulated robotics in airframe assembly. With the addition of secondary feedback, high-order kinematic model, and a fully integrated conventional CNC control, robotic technology can now compete on a performance level with customized high precision motion platforms. As a result, the articulated arm can be applied to a much broader range of assembly applications that were once limited to custom machines, including one-up assembly, two-sided drilling and fastening, material removal, and automated fiber placement.